The detachable laser head contains its own driver board so can operate from a 5V mains adapter or batteries. High power, adjustable focus.

• Specification
• Wavelength : 405nm +/-5nm
• Output Power : 200mW before cross-line generator, 150mW output as cross-line
• Operating Voltage: 5.0V,  5.5 x 2.1mm socket
• Current: <210mA controlled by ACC driver circuit
• Dimensions: 16mm diameter x 110mm
• Pattern: Cross pattern
• Lifetime: >4000hrs
• Operating Temperature: 10 – 40°C

Specification

• Size: 16mm x 64mm
• Voltage range: 5.0V 5.5 x 3.1mm socket
• Operating Current: <220mA
• Driver Type: ACC Boost
• Diode Output: 200mW
• Wavelength: 405nm +/- 5 nm
• Projected pattern: dot with adjustable focus (cross or line with optional generator disc)
• Operating temperature: 10 – 40°C

Specification

• Size: 16mm x 64mm
• Voltage range: 5.0V 5.5 x 3.1mm socket
• Operating Current: <450mA
• Driver Type: ACC Boost
• Optical Output: 300mW
• Wavelength: 405nm +/- 5 nm
• Projected pattern: dot with adjustable focus (cross or line with optional generator disc)
• Operating temperature: 10 – 40°C

• Class 3B Laser product

• Class 3B Laser product

500mW 405nm laser with optional TTL/PWM control (laser engraving).

• 405nm laser based on BDR-S06J diode.
• Genuine 500mW output
• 12V operation.
• Option TTL/PWM modulation
• Fine focus (minimum dot diameter ~ 0.3mm)

12V (1A) power supply required.

405nm wavelength gives a smaller spot size than 450nm lasers and is more effective for exposing photoresist and cutting than the equivalent power 450nm laser.

Notes: 

1.     Refer to the diagram for connections.

2.     The laser driver board has separate power and TTL/PWM connections. Power is 12V (VCC+ and VCC-). It is important that 12V is not connected to the TTL input or the driver will be damaged. (TTL signals are ~4-5V).

3.     Driver board has a dimmer button, if this is depressed the laser will output a very low output to allow focusing without marking a target. Pressing the button again will bring the laser back to full power.

4.     With no connection to TTL the laser is normally on.

5.     If TTL or PWM control is required, the supplied cable should be plugged into the driver board where shown. For TTL action, connect the wires together to blank the laser, the black wire (ground) will pull the red (high) wire low or apply a TTL level (5V) signal. Pulse switching up to 20kHz can be used to reduce the output of the laser (PWM).

6.     The optional 3-wire cable can be used with some laser engraver controller boards to provide PWM and power with a single cable.

• Wavelength: 405nm
• Optical Power: 500mW
• Operating Voltage: 12.0V
• Operating Current: 500mA
• Operating Lifetime: >4000hrs
• Operating temperature: 10 - 40 °C
• TTL Control: 20kHz @5V
• Laser Head Dimensions: 40mm x 40mm x 90mm
• Adjustable Focus, 0.2mm dot at 5-25cm
• Requires 12V power supply with at least 1A output

CLASS 3B LASER - Eye protection required.

Operation

This module has adjustable focus and optional TTL switching that can be used to control the power output (normally on full power, the TTL signal can be used to reduce the output power using PWM). 12V operation. Cooling fan. Normally on with power supplied.  Low power latch switch to allow easy focusing.

• Wavelength: 405nm
• Optical Power: 500mW
• Operating Voltage: 12.0V
• Operating Current: 500mA
• Operating Lifetime: >4000hrs
• Operating temperature: 10 - 40 °C
• TTL Control: 20kHz @5V
• Laser Head Dimensions: 40mm x 40mm x 90mm
• Adjustable Focus, 0.2mm dot at 5-25cm
• Requires 12V power supply with at least 1A output

CLASS 3B LASER - Eye protection required.

Operation

This module has adjustable focus and optional TTL switching that can be used to control the power output (normally on full power, the TTL signal can be used to reduce the output power using PWM). 12V operation. Cooling fan. Normally on with power supplied.  Low power latch switch to allow easy focusing.